HOME/CAR/ANYTHING AUTOMATION ((( ThE Easy Way )))

[allalone747]

read this

https://groups.google.com/forum/#!topic ... bIO2wHK1KU

Hi there thank you for the link you send , but some how i am getting Malware warning from these pages,
Malware Warning

Warning – visiting this website may harm your computer!


http://www.logix4u.net/parallel-port/26 ... -xp-64-bit
https://www.google.com/url?q=http%3A%2F ... d7Rx-NDf9g
https://www.google.com/url?q=http%3A%2F ... d7Rx-NDf9g

also according to the read up files the InpOut32 doe's not support USB parallel ports or the PCI parallel port, as i have a computer that don't have the old Parallel port built on it would not work,
is there an alternative, i tried Dos Box ,this also do not work, any idea out there please
Thank you

Hello every body , good day , my last post here on this subject, the file that i am trying to run is lptout.exe
when i try to run it i am getting this error "This app can't run on your PC", i am using Windows 10 64 bit
I try running it through DosBox but still no result, i have tried several methods but none seems to work,
i cannot upload the file,
thank you
cheers

[allalone747]

Hello every body , good day , my last post here on this subject, the file that i am trying to run is lptout.exe
when i try to run it i am getting this error "This app can't run on your PC", i am using Windows 10 64 bit
I try running it through DosBox but still no result, i have tried several methods but none seems to work,
i cannot upload the file,
thank you
cheers

[Zunair]

right click the file, properties, make sure unblock is checked if you see something about blocking.

Sent from my SM-G950U using Tapatalk

[Classifiedness]

the file is 32bit so it needs a windows 32bit

[allalone747]

Hello
I am now using Windows 7 32 bit PC, motherboard had a build in Parallel, I will explain what results I am getting from this setup, the 3 volts light emitting diode is plug in the LPT port the plus leg in pin hole D0 the negative leg in pin hole 18, I switch on PC the 3 volt light come on, then went off during booting, then come on again and stay on during booting onto desktop.
I then type CD\lpt enter then lptout 0 the light stay on, I then type lptout 2 the light now go off
I then type lptout 255 it still stay off. I then try lptout1 it remain off,
I then power down the PC the light then come back on and stay on until the PC complete the circle the tutorial say type lptout 0 to turn off , but this does not happen, lptout 2 does, therefore at this point I am unable to turn ON/OFF this setup.
Question, did anyone really get this to work, none of the command in the tutorial work
LPTOUT 2 not mention, I do hope someone can advice me on this, I love to get it going, so please your help
Thank you

[allalone747]

right click the file, properties, make sure unblock is checked if you see something about blocking.

Sent from my SM-G950U using Tapatalk

Hi there I checked to see if there was any method in properties but there was none to unblock ,

[allalone747]

Any reply please

[Zunair]

I would reply if i tried using it... Sorry

Just get Arduino NodeMCU and play with that instead of the ol' ltp!

[Classifiedness]

it is so easy, just make sure to connect the L.E.D the right way

lptout 0
Set all LPT pins from ((( 2 to 9))) to OFF

don't forget D0 is pin 2 - D7 is pin 9

and don't forget to put the correct values

1 2 4 8 16 32 64 128

for example :
set pin 2 and pin 3 and pin 4 to all ON
7 is the sum of 3 pin values which are 1+2+4

here is how to connect the L.E.D to pin 2 known as D0



Hint: make sure that the printer port is configured correctly and is working fine , to do that make sure that it is enabled from Bios and is configured as " ECP Mode"

[bbvideo=560,315]https://www.youtube.com/watch?v=FHCvrn9B6W0[/bbvideo]

[Classifiedness]

get ready guys , we are now getting wireless

new thinking , new ideas , new ways